← All tools

Tuning, voice and ear training

Online tuner

Tune one note at a time with your microphone. Choose your instrument and lock a target when you need to tune a specific string.

ONE NOTE AT A TIME

Your tuning workspace

Enlarge the note and meter. All settings remain available.

NOTE / TARGET

—

Waiting for a sustained note

Cents · expanded center scale

← Flat · Sharp → · Slower as you get closer

Compare intonation · open / fret 12

Capture the open string, then fret the same string at fret 12 with normal pressure. The target switches to Automatic after the open-string capture.

—

—

This compares frequencies; it is not an automatic instruction to move the bridge. Pressure, strings and instrument setup affect the result.

Choose Automatic or select a string chip to lock its note. ♪ plays a reference.

Input, range and calibration

Microphone level in HertzKit

100% · 0 dB
—
—

Start at 100%. This control changes the level within HertzKit, not the hardware gain. If the incoming signal is already distorted, lower the system or interface input. Increasing gain also increases noise. This setting lasts for the session.

Calibrate with an external reference · optional

Use only with an external source of known frequency. Do not use this tuner’s own tone. The correction applies to this input and session.

History and spectrum

Last 6 seconds · the history reference band is ±5 cents

Input spectrum · 25–3000 Hz

Tune in three steps

  1. Choose your tuning Choose your instrument’s tuning to guide detection. Chromatic remains available for any note.
  2. Play and let it settle Start the microphone, play one string and mute the others.
  3. Adjust and check again A reading to the left means the note is flat; to the right, sharp. Make a small adjustment and play again gently.

Use “Enlarge reading” to see the note and meter from farther away. “Normal view” restores the layout; Escape also returns when you are not editing a field. Microphone and tuning settings stay as they are.

For standard guitar, start with the sixth string: E2. The initial confirmation tolerance is ±2 cents. Read the step-by-step guide →

Examples by instrument
  • Guitar. In standard tuning, play the open sixth string (E2). Let the initial attack settle and adjust after a gentle pluck.
  • Bass. On a four-string bass, start with E1. If the reading jumps an octave, try the low range and mute the other strings.
  • Violin. Select Violin and start with open A4. Bow steadily without vibrato and wait for a stable reading.

With a stable reading, −4 cents means the note is below the target. +4 cents means it is above.

Frequently asked questions

Can I keep my phone or tablet screen on?

On touch devices, enable “Keep screen on” next to the controls. It applies to this visit only and turns off when you press Stop or leave the page. The page must stay visible; it does not keep the microphone running in the background. Your browser or battery-saving settings may prevent activation or release it later. Check that the status says “Active”.

How do I use the bowed-string and mandolin tunings?

The buttons list open-string notes from low to high. Violin and mandolin share G3–D4–A4–E5; viola uses C3–G3–D4–A4, and cello C2–G2–D3–A3. On mandolin, tune one string of each pair at a time. Targets use twelve-tone equal temperament and the selected A4 reference; they do not apply pure-fifth or ensemble-specific adjustments. Fret-12 comparison is intended for fretted instruments.

How do I read the display and string marks?

Wait for “Stable reading”. Cyan indicates the selected tolerance. A string chip is marked after 0.6 stable seconds within that zone; it remembers the session, but the string can drift later. Fine reading shows tenths: that is resolution, not certified 0.1-cent accuracy. Signal messages appear when a condition persists, avoiding brief flashes. The meter enlarges the scale near zero; its marks show cents of pitch deviation. The needle and number show the same filtered reading. The selected tolerance keeps its meaning.

What if the reading jumps or shows another octave?

Play one note at a time and let the attack settle. Under Input, range and calibration, choose a range that includes the note and check the level. Noise, vibrato and strong harmonics can confuse the reading. Choosing a tuning or locking a string helps distinguish competing pitches; it does not change the measured frequency or snap it to the target. A full chord cannot check each string with this tuner.

Is calibration or audio saved?

Input correction lasts only for this session and is removed when the input changes. The tuner does not record or upload your audio. The microphone stops when the tab goes into the background.