PRACTICAL GUIDE
How to tune a guitar step by step
From six open strings to a stable reading. Follow the steps and open additional options when you need them.
On this page7 sections
1. Get the six strings ready
In standard tuning, from the sixth string—the thickest—to the first: E, A, D, G, B and E. These values use A4 = 440 Hz.
| String | Note | Frequency |
|---|---|---|
| 6th | E (E2) | 82.41 Hz |
| 5th | A (A2) | 110.00 Hz |
| 4th | D (D3) | 146.83 Hz |
| 3rd | G (G3) | 196.00 Hz |
| 2nd | B (B3) | 246.94 Hz |
| 1st | E (E4) | 329.63 Hz |
2. Tune one string, then repeat
- Choose Guitar — Standard in the tuner and start the microphone. Find a quiet spot.
- Start with the sixth string, E2. Select its chip to lock the target. The ♪ button lets you hear a reference.
- Play one string and let the attack settle. Mute the others and wait for “Stable reading”.
- Adjust a little at a time: left means flat; right means sharp. Aim for the center. The initial confirmation tolerance is ±2 cents.
- Repeat with the other strings and check all six again. If you overshoot, loosen slightly and approach from below. Pluck gently again to check.
If the instrument keeps you farther from the screen, use Enlarge reading in the tuner. The note and meter grow without changing your target or microphone. All settings remain available, and Normal view restores the original layout.
3. Understand the reading
Note and deviation
Automatic identifies the note; a locked target compares against the note you chose. Cents show how far you are from it.
Stability and confirmation
Wait for a stable signal before fine adjustments. Cyan indicates your chosen tolerance; a string mark remembers the session and should be checked again.
Fine reading shows tenths; select the tolerance beside the target controls. Displaying 0.1 cent does not guarantee that accuracy with every microphone. Use a sustained note for the adjustment. If the reading is not stable, pluck again before turning the tuning peg. Understand cents →
When should I change A4?
The musical reference
Leave it at 440 Hz unless your ensemble uses another reference, such as 442 Hz. A4 accepts 400–480 Hz. Changing it clears earlier marks and changes the expected frequency of every note. It does not calibrate the microphone.
4. Compare intonation, if needed
If the open strings are in tune but chords sound off in other positions, compare the open note with the same string fretted at fret 12.
- Open Compare intonation in the tuner and capture a stable open string.
- The target switches to Automatic. Fret at fret 12 with normal pressure and capture the second note. Do not use the fret-12 harmonic.
- Repeat several takes with the instrument in the same position. A positive value means the fretted note is sharp relative to the octave.
110 Hz open and 220 Hz fretted form an octave. At 220.64 Hz, the difference is approximately +5 cents. The comparison is a reference; it does not by itself tell you how far to move the bridge.
5. Other tunings and methods
The selector includes these tunings. For another combination, choose Custom and enter comma-separated notes with octave numbers, such as E2,A2,D3,G3,B3,E4.
| Tuning | Strings (6th to 1st) | What changes |
|---|---|---|
| Drop D | D A D G B E | Only the sixth string drops a whole step, from E to D. It extends the low register and lets you play power chords with one finger across the lowest three strings. |
| Half step down | Eb Ab Db Gb Bb Eb | All six strings drop a semitone. With the same strings, tension is lower and bends may feel easier. If you sing, check both high and low passages before choosing it. |
| DADGAD | D A D G A D | The sixth, second and first strings each drop a whole step. Widely used in folk and fingerstyle. |
Tuning upward increases tension: proceed gradually and use strings suited to your instrument.
Bass and ukulele
Choose the instrument’s tuning
The tuner also includes four- and five-string bass, and ukulele. On a four-string bass the notes are E, A, D and G (E1, A1, D2 and G2); the five-string adds a low B. On a standard ukulele the strings are G, C, E and A, with the G tuned higher than the C, so the strings do not run from low to high.
Without a tuner: compare strings
Relative tuning
If you already have the sixth string in tune (from a tuner, a tuning fork or a piano), you can tune the rest by comparison. Press a finger on the 5th fret of one string and compare the sound with the open string next to it: the 5th fret of the sixth string matches the open fifth string, the 5th fret of the fifth matches the open fourth, and the 5th fret of the fourth matches the open third. Between the third and second strings it changes: to reach the second string you press the 4th fret of the third. Then the 5th fret of the second string gives the open first string.
It is slower and depends on your ear, so it is a way to get by. Check with the tuner as soon as you can.
6. Troubleshoot a difficult reading
The note jumps, disappears or changes octave
Mute the other strings, move away from speakers and pluck gently. Under Input, range and calibration, choose General (40–1600 Hz), Bass (25–600 Hz) or High (150–3000 Hz). The correct range helps; periodic noise and strong harmonics can still confuse the reading.
There is no signal or the level is too high
Microphone input and level
Allow microphone access and check the selected input under Input, range and calibration. Refresh inputs if you connected another device. Start at 100% and watch the meters. If the incoming signal is already distorted, lower the system or interface gain: lowering the web level cannot repair it. Increasing the level also increases noise.
The guitar goes out of tune again
Strings and changing conditions
A newly fitted string stretches over the first few days and goes out of tune quickly. It helps to pull it gently upward along the neck, without overdoing it, and retune several times. Temperature and humidity also move the tuning, so it is better to tune at the start of every session rather than once a week.
Do I need to calibrate the input?
It is not a required step to get started. The advanced option needs a reliable external source of known frequency. This tuner’s own tone cannot calibrate its input. The correction lasts for the session and is removed when the input changes.