← All tools

Rhythm & tempo

Delay & reverb BPM calculator

Choose a tempo and note value. Copy the timing for your delay or read the matching LFO frequency.

Tempo timing

Local calculation · no audio upload

20–300 BPM

Duration

Eighth · straight

250.00 ms

4.000 Hz · LFO

Copies the number only, with a decimal point.

120 quarter-note BPM · 500 ms per quarter

Hear your setting

Delay · 250 ms

Change the tempo or note value and press “Play my setting” again. Listen for two echoes in Delay and the gap before the same reverb tail in Pre-delay.

Timing tableStraight, dotted and triplet · ms
120 BPM · quarter note · ms
NoteStraightDottedTriplet
Whole1/1
Half1/2
Quarter1/4
Eighth1/8
Sixteenth1/16
Thirty-second1/32
Sixty-fourth1/64

Select a cell to show that duration in the panel.

Fixed examples for your DAW

The examples use the same synthesized hit as the interactive preview. Play one at a time and compare the echo spacing or the onset of the reverb.

Delay at 120 BPM: 250 ms versus 375 ms

Straight eighth · 250 ms

Dotted eighth · 375 ms

Listen to the spacing before the first repeat. In the DAW, choose free time in ms, paste the value and compare at the same feedback and mix. If the plug-in is in sync mode, select the matching note value. Feedback controls how long the repeats persist.

Reverb pre-delay

Start with “No reverb” to hear the hit on its own. At 0 ms, the tail starts with the hit and can sound louder. At 31.25 ms, the same hit is more distinct from the tail.

No reverb

Reverb · 0 ms

Reverb · 31.25 ms

On a reverb send, keep the decay fixed and vary the pre-delay. Listen for a clearer attack and check it in context. A tempo-synced value gives you a starting point.

A 6/8 example and a quick check

If you count 60 dotted-quarter pulses per minute, each pulse takes 1000 ms and contains three eighth notes of 333.33 ms. Select that beat unit. If your DAW already shows 90 quarter-note BPM, enter 90 in Quarter note mode to get the same result.

If you are unsure of the tempo, open the BPM Detector and check the click before bringing the value here. To study the low frequencies and decay of your space, use the room acoustics calculator.

Audio sources

From tempo to effect

  1. Enter the tempo. Keep “Quarter note” when using your DAW's BPM. If you counted a 6/8 beat in dotted quarters, select that unit.
  2. Choose a note value and duration: straight, dotted (× 1.5) or triplet (× 2/3).
  3. Copy milliseconds into the effect's time control, or Hz for an LFO. Starting points keep your tempo and beat unit. Check in metronome opens the equivalent quarter-note tempo without starting sound.

Delay

This value sets the interval between repeats. At 120 quarter-note BPM, a straight eighth lasts 250 ms; a dotted eighth lasts 375 ms. Feedback controls how many repeats you hear.

Reverb pre-delay

The wait before reverberation begins. At 120 BPM, a straight sixty-fourth gives 31.25 ms. Treat it as a starting point to audition, rather than a required setting.

Reverb decay

The time the tail takes to fade. It is separate from pre-delay. You can compare its duration with the tempo, but choose it for the pauses, density and intention of the arrangement.

How the calculation works

For quarter-note BPM: quarter duration in ms = 60,000 ÷ BPM. For a note 1/n: ms = quarter duration × 4 ÷ n. Dotted notes multiply by 1.5; triplets by 2/3. Frequency is 1,000 ÷ ms.

Dotted-quarter BPM is converted to quarter-note BPM by multiplying by 1.5: 60 beats per minute equal 90 quarters per minute. Displayed results are rounded; calculations retain full precision.

Frequently asked questions

Does the calculation change if I count dotted quarter notes?

Select “Dotted quarter” under Tempo beat unit. Conversion is automatic: 60 beats per minute equal 90 quarters per minute. Keep “Quarter note” for DAW BPM.

Does the calculator choose the best reverb setting?

No. It calculates rhythmic durations and frequencies. Effect amount, feedback and decay should be chosen by listening to the available space and the intended mix.