Mixing and Mastering Workshop
Hear what compression, EQ and limiting change. Compare before and after, then repeat each exercise with the effects in your DAW.
Exercises with recorded piano, guitar, upright bass and drum samples at 120 BPM. Any audio you load is processed on your device.
Workshop exercises
Exercises use example recordings or the audio you load in this workflow.
Source and exercise
WAV or MP3, mono or stereo. Load up to 10 minutes and 128 MB. Compare a passage of up to 30 seconds.
Example with recorded instruments
A/B monitoring
Select a passage
Selection
File duration
Moving the selector updates A/B to the new passage.
Choose A to hear the original passage and B to hear the settings. Playback headroom and loudness matching affect monitoring only.
Controls change B. Switch to A to compare.
Select B to hear changes as you move the controls. The meters update when you pause or release the control.
Measurements and DAW settings
Settings to recreate B in your DAW
| Version | LUFS | Sample peak (dBFS) |
|---|---|---|
| A | — | — |
| B | — | — |
Sample peak and true peak are different measurements. Compensation applies only to playback.
Export the track with your settings
Download the entire track as 24-bit PCM WAV at 48 kHz. Choose where to apply B’s settings.
Worksheet
How to repeat the exercise with your DAW effects
Starting settings for your DAW
Use your DAW’s stock effects. Start with these settings and adapt them to the recording. The TXT worksheet saves both the workshop settings you tried and this reference.
To listen to each effect separately: EQ with purpose and hear and adjust a compressor.
Calculate a tempo-synced delay
Calculate a time value for your delay plug-in. This control does not change the Workshop audio. Enter the BPM and choose a note value. For example, at 120 BPM an eighth note is 250 ms.
Use the result in your delay’s time control when it is in milliseconds mode. Set feedback and effect level while listening to the mix.
What to try by instrument
- Vocals
- Automate words that get lost. Compress if peaks still distract.
- Drums and percussion
- Compare attack and tail. Adjust the envelope or try compression to reshape the hit.
- Bass
- Check it against the kick. Adjust length and level before cutting frequencies.
- Guitars
- If they mask the vocal, try level or panning, then a targeted cut.
- Keys and synths
- If they take up too much space, try a different octave or a shorter reverb.
- Strings and winds
- Keep the articulation. If one note dominates, try automation before compressing the whole part.
To add depth while keeping clarity, try reverb on a send. Bring up the return until you hear it, back it off slightly, then check that the part keeps its place when the rest comes in.
Settings for stock effects
- EQ
- For a bell, start with ±2 dB and Q 1. Cut to make room or boost for presence. Return to 0 dB if the balance gets worse.
- Compressor
- Try 2:1–3:1, 10–30 ms attack and 80–150 ms release. Set the threshold using gain reduction. If the attack loses life, lengthen the attack time or ease off.
- De-esser
- Find the offending sibilance; 5–8 kHz is a starting range. Aim for the effect to act on those syllables. Ease off if the whole voice becomes dull.
- Gate or expander
- For noise between phrases, try gentle expansion with 100–250 ms release. Set the threshold on the softest phrase. Lower it or lengthen release if it cuts off endings.
- Reverb
- Set a send effect to 100% wet. Try a 0.6–1.2 s room and 15–30 ms pre-delay. Set the level at the return and shorten the tail if it masks the next phrase.
- Delay
- Calculate the time from the song tempo. Try 10–25% feedback and a low return level. Reduce feedback if repeats crowd the next phrase.
- Saturation
- Raise the input gradually and match output to bypass. Back off or remove it if it adds harshness or reduces definition.
Assisted mastering
Create a proposal for your mix and compare it with the original. Audio is processed on your device.
1. Load your mix
Mono or stereo WAV up to 5 minutes and 128 MB per file. Output is 24-bit PCM WAV at 48 kHz.
Adjust loudness and peak · optional
The target guides the adjustment. Peak protection may yield a different loudness. The reference guides EQ while you choose the loudness target.
Manual EQ and presets · optional
Adjust up to ±3 dB per band. Manual settings are added to reference-guided EQ. Generate another proposal to hear them.
My presets
Presets store EQ, target, ceiling and influence in this browser. Choose the mix and reference separately.
In Automatic mode, HertzKit keeps the input loudness as the target when it is between −18 and −12 LUFS. Without a reference or manual EQ, it leaves the tonal balance alone.
If you change the target or reference, generate a new proposal. You can switch A/B during playback.
2. Listen and compare
Press Play and switch versions at the same point. Loudness matching applies only to playback.
- Original mix
- Proposal WAV
- Reference
What changed in the WAV
See applied settings
| Band | Original | Reference | Proposal |
|---|
3. Download and review the WAV
If you prefer the proposal, download it. In the review tool, load your mix in A and the downloaded WAV in B.