Generate & process audio
LUFS meter
Measure your track’s loudness, dynamics and peaks. Explore a gain simulation and save the report, without changing the audio.
Looking for a different task? Explore the spectrum and analyse excerpts · Review listening points and check mono.
1 · Load and listen
MP3 or WAV · up to 10 min and 128 MB · mono or stereo.
Tap the waveform to seek. The whole track is always measured.
Volume affects playback only.
Measurement runs on your device and does not modify the original file.
2 · Review loudness
Load your audio and choose Measure loudness to see results.
Loudness of the whole track.
Loudness over time
Thick cyan: short-term (3 s). Thin line: momentary (400 ms). Dashed amber: integrated loudness. Shaded band: LRA. Use arrows to inspect a moment and Enter to select it. You can also click or tap the chart, then use Listen from here.
3 · Compare a reference (optional)Estimate uniform gain without changing your audio.
These are comparison references, not universal targets or a prediction of platform playback volume. The simulation assumes uniform gain without limiting or clipping. Encoding or processing can change the peak: measure the exported file. No gain or normalization is applied.
What each measurement meansUnits, time windows and interpretation limits.
- LUFS
- Weighted loudness relative to digital full scale. Integrated loudness describes the measured file, rather than only its loudest passage.
- LRA · LU
- Loudness range. Interpretation is limited for short content.
- dBTP
- Estimated true peak between samples. It differs from the sample peak in dBFS.
- PLR · LU
- Difference between estimated true peak and integrated loudness.
Calculations use the HertzKit loudness engine, with K-weighting and gating, for mono or stereo. True peak is estimated and this meter is not certified. For deliveries with strict tolerances, check against a calibrated reference and the recipient’s specifications.
Same LUFS, different attack
Listen to A and then B at the same device volume. Both use the same eight-second passage and are matched for integrated loudness. Listen to the drum attacks in the first bars.
A · Uncompressed
- Integrated loudness
- −20.0 LUFS
- Estimated true peak
- −4.1 dBTP
- PLR
- 15.9 LU
B · Compressed
- Integrated loudness
- −20.0 LUFS
- Estimated true peak
- −9.8 dBTP
- PLR
- 10.2 LU
A keeps the higher peaks. Compression in B softens the attacks and leaves more peak headroom. PLR is the gap between estimated true peak and integrated loudness. For this short excerpt, use it alongside listening to compare the attacks.
Before delivery, compare at matched loudness and measure the exported file against the delivery specifications.
How to use the meter
- Choose a file or Try a piano example. Playback does not change its measurements.
- Choose Measure loudness. The whole track is measured, regardless of the playback cursor.
- Review integrated loudness, peaks and the chart. Select a moment on the chart to listen from there.
- To estimate a gain change, open Compare a reference and enable the simulation. Export report includes it only when enabled. No gain is applied to audio.
Try a practical example
Try the piano, listen and measure it. In Compare a reference, enable the simulation and choose a higher reference: check whether its estimated peak would exceed the ceiling. The audio stays unchanged; this is a way to understand the available headroom.
Files and progress
Up to 10 minutes and 128 MB per file, mono or stereo. Both limits apply. Supported formats and available memory depend on your browser and device; if you have trouble, try a shorter excerpt.
Measurement runs in several stages. Use “Cancel measurement” while it is running. After canceling, choose the file again to retry. Selecting another file discards the previous measurement.
Frequently asked questions
Does measuring LUFS normalize or modify the file?
No. This tool measures and displays references. To adjust level, use the editor or your DAW, then measure the exported file again. Results depend on the audio decoded by your browser.
Should I always master to −14 LUFS?
No. It is an informative playback reference, not a universal mastering target or publication requirement. Follow the music and delivery specifications. Volume normalization cannot repair distortion or restore lost dynamics.